General
Design of Latticed Steel Transmission Structures specifies requirements for the design, fabrication, and testing of members and connections for electrical transmission structures. These...
Potential Flow Instability Theory and Bed Forms
An extended, generalised version of two-dimensional linearised potential flow theory of fully unsteady fluid flow-sediment bed interaction is presented. In contrast to previous potential...
Review of Cold-Formed Steel Purlin Design
The use of cold-formed steel members as roof purlins for single story industrial and commercial buildings is commonly recognized. These members typically have either a C- or Z-shaped cross...
How to Optimize Light-Gage, Cold-Formed Steel Beams
The Illustrative Examples section of the AISI Cold-Formed Steel Design Manual (AISI 1989) demonstrates how to analyze a number of different cold-formed steel sections. This paper applies...
Is Bedform Development Chaotic?
A qualitative analysis of a model for the partially specified bedform development system is presented. The study rests on the use of technique of loop analysis and the connection of the...
Highlights of the New ASCE Standards on Composite Deck Floor Slabs
This paper presents highlights of the newly approved and printed ASCE Standard on the design and construction of composite floor deck slabs utilizing cold-formed steel. In 1992 four documents...
Design of Latticed Steel Transmission Structures
This standard,
Data Modelling for Steel Frame Structures
The first step to automate any facet of structural engineering is developing a suitable data representation upon which the computer program will operate. However, there is no standard...
Conglomeratic Shoreface Deposits from the Cretaceous Cardium Formation, Alberta, Canada
Conglomeratic shoreface deposits of the Upper Cretaceous Cardium Formation are well exposed at an outcrop in northwestern Alberta. The conglomerates there compose over 80% of the total...
Bed Forms of Nile River
In this paper, the observed bed forms for six different reaches of the Nile River in Egypt are described. The purpose of the study is to inquire whether or not the different available...
Specification for the Design of Cold-Formed Stainless Steel Structural Members
ASCE's standard
Bed Sediments and Bed Forms of the Lower Mississippi River
Approximately 500 bed material samples were collected from the thalweg of the Lower Mississippi River. At each sample location, a sonic record of the bed was obtained. From the appearance...
Variational Method in Fluvial Hydraulics?A Review
The theoretical base of the principle of minimum energy dissipation rate and other related stationarity hypotheses have been reviewed. Recent applications of the theory to the calculation...
New Outlines for 500 kV Transmission Towers Using Cold-Formed Shapes: The Experimental Line of the American Electric Power Research Institute
The use of cold-formed steel members, in electrical transmission towers, is actually a feasible, reliable and economical solution. The EPRI experimental line is an example of the newest...
Design Issues in Steel Buildings
The Committee on Design of Steel Building Structures of the Committee on Metals of the Structural Division of ASCE was formed in 1981, with the express purpose of studying problems that...
Steel Girt Design
Procedures are presented for the design of light gage cold formed girts and hot rolled girts. The effects of continuity, sag rods, and wall sheeting are discussed. Design procedures are...
Behavior of Cold-Formed Steel-Concrete Composite Beams
An experimental investigation was conducted at California State University - Long Beach to study the structural behavior of composite beams made of thin-walled cold-formed steel stiffened...
Cold-Formed Z-Sections Under Axial Load and Bending
The use of cold-formed Z-section members as beam-columns presents some unique design problems which are not adequately addressed in the current design specifications. If these members...
Automated Load Capacity Determination of Cold-Formed Steel Compression Members
This paper presents an automated approach for the evaluation of the axial load capacity of nine cold-formed steel sections according to the latest AISI-1986 Cold-Formed Steel Specification....
Weathering Steel Bridges ? State of the Art
State of the art dissertations on materials that have been in commercial use for over a century are not likely to illustrate major new and innovative breakthroughs. Instead, the state...
Return to search